5.5 How do I add one of the 8 internal effects to the sound? Highlight output 1 (01 @). Open the ROUTING menu on your X32 and Navigate to the CARD tab. Learn how to get sound out, route signal, and record audio. That is the next step.

MacOS: The X-USB is CoreAudio compatible and thus works with low-latency on Mac computers without any additional driver installation. You should also see the expansion card as an input option with your streaming software (OBS, FB Live, YouTube etc). This guide is intended to assist with setting up a stereo output stream from your X32 to a streaming software like OBS or FB Live. Once done, press ENCODER 6 to assign the IP settings and join the network. Using the X32 digital mixer is not all that different from a typical analog mixer, but the navigation and digital controls add another layer of accessibility. 5.13 What kinds of Utilities are available? There are multiple drivers available but that is because they are for the different expansion cards.

“Q” versions are also available for iOS and Android devices and are ideal for a performer to control their personal monitor mix. Check out the video below to learn more about the X32’s TFT screen and continue reading to get started.

Wired is pretty simple, just connect your computer’s ethernet port to the X32’s ETHERNET port. You can control your X32 with its faders and knobs or remotely using the X32 Edit app. These screens will allow configuring the X-USB expansion card in the X32 RACK as an audio interface for your computer. 1. MacOS: The X-USB is CoreAudio compatible and thus works with low-latency on Mac computers without any additional driver installation. The X32 is a digital mixer, which means it is just like an analog mixer but with the advantages of digital routing, recallable settings, DSP processing, and even wireless remote control. Happy customers, one piece of gear at a time! is controlled by the same set of encoders and buttons, you just have to select the channel. 5.7 Everything you ought to know about Solo and monitor sources. 5.4 How do I add one of the 8 internal effects to the sound? Select the driver that matches your expansion card (X-USB, X-UF, X-LIVE). Raise the digital faders for 1-2. Follow the sections below to get input signal and then output sound to the main speakers. Now that you have either your pair of busses or your Main Mix ready to be sent out to the stream, SELECT either the Main LR or MIX BUS 1. Now, after connecting via USB to your computer from the expansion card, you should see that your Mac or PC recognizes that the expansion card has been connected and  you should have options within your operating system’s sound settings to choose the X-USB, X-UF or X-LIVE as your Playback or Recording device. 5.8 How do I share signals over AES50 Supermac network? Follow the sections below to get started. A microphone with enough gain is good for setting speaker levels, but you can also connect a phone or tablet to an AUX input to play back line level audio.

You will notice that on the right side of the menu you can see a breakdown of which signals are routed to the outputs.

Now is the perfect time to get the gear you want with simple, promotional financing. Digital features aside, the mixer works as you’d expect, but instead, a strip of controls for each channel the digital channel strip section always controls the currently selected channel(s). Select the Expansion card as the input device. Each X32 model may differ in how many faders, buttons, and encoders it has, but they all share the same navigation screen. 5.5 How do I use an outboard effects processor? The ’Settings’ screen allows the stream, ASIO, and WDM sound buffers to be set. All rights reserved. Press the DOWN arrow (Layer Down) button to expose the Mode 1-2, Mode 3-4 and Mode 5-6 options above the 1, Finally, open the MATRIX bank of faders on the X32 and raise the faders for MATRIX 1-2, You should now be able to hear and see your mix signal present in the streaming software.

After that, we’ll show you how to connect a microphone and get sound to the main speakers. The app is compatible with iPad, PC, and Mac and can be done via a wired or wireless connection. You will have to decide if you want the mix going out to your stream to be identical to the Main Mix (the House mix) or if you need it to be a separate mix.

For example, if you connect a USB 3 device to USB 2 port, your device is limited to USB 2 speeds, and it can't draw more power from the port than can be delivered over USB 2. When you’re finished learn more in our X32 Getting Started Guide. 5.14 How do I set up a Matrix for a delay column/tower or a remote zone mix? The ’Devices’ screen displays the card name and serial number. 192.168.1.120).

Learn More. Double-click on Setup.exe in the corresponding unpacked folder and follow the instructions on the screen.

You can rename the card if necessary. The ’Output Channels’ screen allows you to name each output channel for more organized mixing.

To send signal to the busses you can use the SENDS ON FADER feature or the HOME>SENDS menu with your channels selected. I installed the USB driver, and can get audio input, but do not get anything sending to the boards output. First, if you are using a PC make sure you have the proper driver installed. Other setups may require manual IP assignment where you input the addresses manually. Navigation screen and channel controls 1.2… The main mix level is controlled by the MAIN fader and outputs signal from OUT 15-16 (X32) or OUT 7-8 (compact, producer, and rack). The Ultranet connection is for connection P16 personal mixers.

Now create your stream mix using the selected busses. If you are instead using a switch or manual IP assignment, take note of the router’s IP ADDRESS, Connect your device to the wireless network and launch the, Speak into the microphone and turn up the. To get output from AUX OUT 1-6, OUT 1-14 (X32) or OUT 1-6 (Compact, Producer, and Rack), you must assign the input or mix bus which will go to each XLR or TRS output. To learn more about our cookie policy, please check our Privacy Policy. X32 COMPACT: Configuring the PC to Interface with the X-USB Card, https://behringerwiki.musictribe.com/index.php?title=X32_COMPACT%3A_Configuring_the_PC_to_Interface_with_the_X-USB_Card&oldid=478, 5.1 Starting up, shutting down, and firmware updates, 5.2 Default setup for connecting to monitoring and P.A. These represent the 6 matrices.

In this guide, we will show you how to set up your X32 digital mixer. The AES50 connection is for S16, S32, SD8, and SD16 digital snakes. systems, 5.7 Everything you ought to know about Solo and monitor sources, 5.15 Using the X32 COMPACT in recording and production studio environments, 5.1 Starting up, shutting down,and firmware updates, Everything you ought to know about Solo and monitor sources, 5.15 Using the X32 Producer in recording and production studio environments. 192.168.1.120), SUBNET MASK (eg. 5.11 Using the X32 RACK in recording and production studio environments, 5.13 Recording a 2-track directly with the console, 5.3 Recording a 2-track directly with the console. Windows: There is an ASIO high-performance driver available for download, which is essential for low-latency audio on Windows computers. You can find the downloads for all of the X32 drivers at: https://www.behringer.com/Categories/Behringer/Mixers/Digital/X32/p/P0ASF/Downloads#googtrans(en|en).